Properties Of Joints Research Articles

Microstructure, Corrosion and Mechanical Properties of Medium-Thick 6061-T6 Alloy/T2 Pure Cu Dissimilar Joints Produced by Double Side Friction Stir Z Shape Lap-Butt Welding

A novel double side friction stir Z shape lap-butt welding (DS-FSZW) process was proposed to achieve excellent mechanical properties of Al/Cu medium-thick dissimilar joints. The influence of welding parameters on weld microstructure and properties of DS-FSZW joint were systematically investigated. It indicated that defect-free medium-thick Al/Cu DS-FSZW joint could be achieved under an optimal welding parameter. DS-FSZW joint was prone to form void defects in the bottom of the second-pass weld. The recrystallization mechanisms at the top and middle of the weld nugget zone (WNZ) were continuous dynamic recrystallization (CDRX) and geometric dynamic recrystallization (GDRX). While the major recrystallization mechanism at the bottom of the WNZ was GDRX. DS-FSZW joint of the optimal welding condition with 850 r/min-400 mm/min was produced with a continuous thin and crack-free IMCs layer at the Al/Cu interface, and the maximum tensile strength of this joint is 160.57 MPa, which is equivalent to 65.54% of pure Cu base material. Moreover, the corrosion resistance of Al/Cu DS-FSZW joints also achieved its maximum value at the optimal welding parameter of 850 r/min-400 mm/min. It demonstrates that the DS-FSZW process can simultaneously produce medium-thick Al/Cu joints with excellent mechanical performance and corrosion resistance.

JURIDICAL REVIEW OF PRENUPTIAL AGREEMENTS

A prenuptial agreement or commonly referred to as a prenuptial agreement is a contract or agreement that is equally agreed upon by a married couple, either before the marriage takes place, or during the marriage bond. In conducting research to be more focused, the author made a formulation of the problem, namely how is the legal provisions of the prenuptial agreement based on Law Number 16 of 2019, how is Amendments to Law Number 1 of 1974 concerning Marriage in Indonesia and the Legal Effects on Marital Property with the Prenuptial Agreement in Indonesia. The type of research used in this writing is normative legal research. Normative research is carried out by collecting data and information about the legal norms you want to research, then analyzing the data and information to get a deeper understanding of existing legal norms. Normative research methods can be carried out by means of literature studies, namely by collecting library materials or legal sources relevant to the research topic. The results showed that the forms of this marriage agreement include marriage agreements with togetherness of profit and loss, marriage agreements with togetherness of results and elimination of togetherness of wealth. The content of the agreement must be discussed carefully. You must ensure that you and your partner agree on the content of the agreement and are consistent with your values. For example, how joint property will be managed and divided if one day you divorce.

Enhancing tensile properties of MIG welded AA6061 joints: Effect of pulse mode and post-weld heat treatment

Metal-Inert Gas (MIG) welding is one of the most important welding technologies commonly used in the manufacturing industry due to its high degree of automation and welding adaptability. However, softening is prone to occur in fusion zone (FZ) and heat affected zone (HAZ) of AA6061 MIG welded joint, which limits its application. In this work, AA6061 was welded by MIG welding with different pulse modes, and the post-welding heat treatment was carried out. The results show that the dual pulse MIG (DP-MIG) and PWHT can significantly improve the mechanical properties of AA6061 butt joint, and its ultimate tensile strength (UTS) is 331.3 MPa, even more than 90% of the base material (BM). In this paper, the microstructure of welded joints under different pulse conditions before and after PWHT was compared, and the relationship between the welding process, microstructure, and mechanical properties was established Furthermore, the influence mechanisms of pulse mode and PWHT on the mechanical properties of welded joints were explained in detail.

Effect of process parameters on joint quality and mechanical properties of local-thickened self-piercing riveted steel and die-casting aluminum joints

Effect of process parameters on joint quality and mechanical properties of local-thickened self-piercing riveted steel and die-casting aluminum joints

Microstructure and Properties of Dissimilar Butt Joints of Aluminum to Copper by Cold Metal Transfer with Preheating

Microstructure and Properties of Dissimilar Butt Joints of Aluminum to Copper by Cold Metal Transfer with Preheating

Wife's Right to Property After Divorce: An Examination of Islamic Law and Legislation in Religious Court Decisions in Yogyakarta City

Indonesia as a sovereign state pays great attention to the rights of its citizens, especially in the context of marriage between men and women, through Islamic family law. Although there are still many divorce cases, the Religious Court as a judicial institution that handles family matters for Islamic citizens, plays an important role in positioning women fairly. However, the importance of wise, intelligent, honest and highly ethical judges cannot be ignored. Judges must be able to understand and apply the law with justice to all litigants, especially in divorce cases where women's rights are often neglected. Research into court decisions is important to see the extent to which judges consider women's interests in their decisions, especially in the context of post-divorce rights that have been formulated in Indonesian Islamic family law. The focus of this research is the wife's rights to post-divorce property as regulated in the legislation, as well as the extent to which these legal products are in accordance with the principles of gender justice. This research uses a qualitative approach with a field study at the Yogyakarta Religious Court. Data were collected and analyzed descriptively analytically, describing events related to court decisions. The gender approach was used to analyze the written law as well as what was decided by the judge in the court process. The results show that the rights obtained by women after divorce in Indonesian Islamic family law, such as the right to mut'ah, the right to maintenance, the right to refuse reconciliation, the right to hadlanah, and the right to joint property, are not discriminated against based on gender. There are no signs of marginalization, subordination, double workload, negative labeling, or violence against woman in Indonesian Islamic family law.

Experimentally Dissociating the Acute Mechanisms of Endplate Fracture Lesions and Schmorl's node Injuries Using a Porcine Cervical Spine Model.

In vitro biomechanical study. This study evaluated the influence of localized trabecular bone strength deficits and loading rate as determinants of Schmorl's node and fracture lesion incidence. The failure load (ultimate compression tolerance (UCT)), loading stiffness, and failure morphology were assessed after acute compression loading and failure. The cartilaginous endplate is vulnerable to injuries such as Schmorl's nodes and fracture lesions. While both injuries are associated with acute compression traumas, the factors that distinguish their incidence are poorly understood. Forty-eight porcine spinal units (domestic hog, 5 - 10 months, ~110kg) were assigned to one of eight experimental groups that differed by initial condition (control, sham, experimentally produced chemical fragility, structural void) and loading rate (3 kN/s, 9kN/s). A servo-hydraulic materials testing system was used to perform acute compression testing until observed failure in the specimen. Post-loading dissection was performed to classify injury morphologies. Between group differences in UCT and loading stiffness were evaluated using a general linear model and injury distributions were evaluated using chi-squared statistics. Schmorl's nodes occurred exclusively in chemical fragility (63%) and structural void groups (37%) and were more prevalent with a 9 kN/s (75%) loading rate, compared to 3 kN/s (25%). In contrast, fracture lesions occurred in all FSUs assigned to the control groups (100%) and the majority of those assigned to the sham groups (92%). No between-group differences were observed for UCT and loading stiffness. Pre-existing strength deficits of the subchondral trabecular bone can alter endplate injury morphology, particularly when coupled with high loading rates, but the localized strength deficits that were associated with Schmorl's nodes did not appreciably influence measured joint properties.

Impact of sound-insulated joints in the dynamic behavior of Cross-Laminated Timber structures

Cross-Laminated Timber (CLT) has gained an increasing success and widespread diffusion among wood products. Due to the novelty of the components and the dry-assembling techniques, certain aspects of its behavior and performance remain unexplored; among these, the use of sound-insulated joints and brackets, along with their possible drawbacks on mechanical performance.In this paper the authors discuss the results of dynamic identification (ID) tests carried out on twin full-size CLT mockups (two-story), one of which was furnished with sound-insulation details based on an elastomeric interlayer. Ambient (white noise and random excitations) and forced vibration (mass shaker) tests were carried out to identify modal parameters.The paper mainly aims at: i) assessing potential differences in the overall dynamic behavior of the two mockups, likely due to the introduction of acoustic insulation, ii) detecting possible drawbacks of insulation layers on mechanical performances, iii) increasing the knowledge about dynamics of CLT structures.The results of Operational Modal Analysis (OMA) are presented and the variations in the dynamics between the mockups are discussed. The construction of finite element (FE) models and their calibration – with joint properties variations – are then presented. The outcomes revealed a drop of modal frequencies values (at least 20 %) upon the introduction of elastomeric insulation, whilst no significant alteration was observed in the mode shapes. Model updating based on the FE models demonstrated that the dynamic response and the frequency variations were mostly associated with wall-to-wall and wall-to-diaphragms joints, and hold-down connections.

Fatigue behaviour and life prediction of self-piercing riveted joints in DP590/AA5754 dissimilar sheets

This paper investigates the fatigue properties of self-piercing riveted joints made by DP590 steel and AA5754 aluminium alloy. The fatigue failure mechanism and fatigue fretting mechanism of the joint were well revealed by analysing the microstructure features of fracture surfaces of sheets and rivets as well as viewing and measuring the distribution and chemical composition of fretting debris. The fatigue life of the joint was also predicted based on the stress intensity factor of the kinked crack of the lower sheet. The results confirmed that two failure modes occurred during fatigue: lower sheet fracture and rivet fracture. During the fatigue failure, cracks appeared in both the lower sheet and the rivets, indicating a competitive relationship between the propagation of cracks in the lower sheet and the rivets. In the range of 40 % and 50 % load level, fatigue crack propagation of the lower sheet is dominant and fracture failure of the lower sheet occurs. Rivet fatigue crack propagation has a significant advantage in the 60 % load range and rivet fracture failure often occurs. It was found that the fatigue failure of the lower sheet is mainly influenced by the main crack, which produces two different morphological sections. Fretting wear of the contact surface was the source of crack initiation, and the fretting debris promoted crack initiation and propagation. Cracks propagate along the width and thickness of the plate, as well as the thickness of the rivet neck. The stress intensity factor range can properly predict the fatigue life of joints.

Development of functionally gradient Cu-Fe based sintered brake pad materials

Abstract The world is seeking a sustainable co-existence with nature to preserve the balance of our ecosystem. This has opened a wider market for green and renewable forms of energy to realize the energy requirements of global countries. Among the various renewable energy sources, harnessing the kinetic energy of the wind through a turbine to generate electricity has seen an ardent growth. Wind turbines, in general, function between 2 m/s and 25 m/s wind speed. When the winds cross the cut-out speed (25 m/s) or during the maintenance of wind turbine components, the brakes are implemented. The primary aerodynamic and secondary mechanical brakes comprise the wind turbine braking system. The mechanical brake pads are fixed to the brake caliper. On braking, the brake caliper pushes the brake pads against the brake disc. This recurring action gradually wears the brake material. The presence of ceramic particles in the traditionally used bulk composite pads imparts poor joint properties between the brake pad and caliper. These mandate frequent replacement of the brake pads. The current research work developed a functionally gradient brake pad through the powder metallurgy technique. The microstructure, microhardness, and tribological properties of the fabricated brake pads are tested and analyzed. Microstructural analysis revealed a homogeneous distribution of the reinforcements in the metal matrix. COF was observed to be within the desired range of between 0.3 and 0.4. The brake pad exhibited a combination of adhesive-abrasive-oxidative wear.

Microstructures and properties of 7075 aluminum alloy and CP780 steel resistance spot welded joint assisted by magnetic field

Joining steel and aluminum is vital for lightweight automobile but still challenging due to their different physical properties. Herein, resistance spot welding tests were performed on CP780 high-strength steel (thickness 1 mm) and 7075 aluminum alloy (thickness 1.5 mm) dissimilar metals under steady-state magnetic field. The influences of magnetic field (B = 40 mT) on the structure of welded joints, the phase composition/content of intermetallic compounds, and tensile properties of welded joints were analyzed under different welding current conditions (I = 9 kA,10 kA, 11 kA, and 12 kA). At the same welding current, the Lorentz force generated by the additional magnetic field promoted the outward circumferential movement of the molten metal in the weld along the horizontal surface , as well as increased the diameter of the Fe/Al contact interface in the weld nugget along the horizontal direction, conducive to the effective utilization of heat of the resistance spot welding. Except under (11 kA-0 mT) and (11 kA-40 mT), welded joints under other welding parameters displayed a few welding defects, such as incomplete fusion and shrinkage cavity formed at the cross-section of the welded joints. Therefore, the synergism between the magnetic field and appropriate welding current held important roles in the formation of welded joints without obvious welding defects. The intermetallic compounds of all the welds were mainly composed of (Fe, Si)Al2 and (Fe, Si)Al5. Meanwhile, the thickness and content of the intermetallic compounds layer reduced under a magnetic field at the same welding current, significantly improving the tensile properties of the welded joints. The comprehensive properties of welded joints were the best under 11 kA-40 mT, with an average shear force increase from 3.02 kN to 3.49 kN (15.56%) and an average displacement increase from 1.01 mm to 1.22 mm (20.79%). Overall, the proposed dissimilar aluminum/steel resistance spot welded joint assisted by magnetic field looks promising for lightweight automobile use.

Enhancement in interfacial bonding quality of CoCrFeMnNi high-entropy alloy vacuum hot-compression bonding via surface shot peening

Vacuum hot-compression bonding (VHCB) is an advanced solid-state bonding technique. To expand its application in high-entropy alloys (HEAs), a new strategy to enhance the interfacial bonding quality of CoCrFeMnNi HEA VHCB joints by surface shot peening (SP) was proposed, and the effects of SP treatment on the interfacial bonding behavior and mechanical properties of VHCB joints were investigated. The results revealed that SP treatment introduced a nanocrystalline layer and plastic deformation layer with non-uniform strain on the specimen bonding surface, and a hierarchical grain size gradient fine microstructure was formed by a static recrystallization process under the thermal activation condition before VHCB. During the bonding process, the fine microstructure of the SP-treated layer was retained and provided a large number of grain boundaries and dislocations, which facilitated atomic diffusion and plastic flow in the interfacial region and promoted the closure of interfacial voids and the dissolution of interfacial oxide particles. Additionally, interfacial crystallographic and tensile test analyses indicated that the SP treatment induced a multiple interfacial grain boundary (IGB) migration mechanism in the VHCB joints, which dramatically improved the IGB migration level and ultimately led to a complete recovery of the mechanical properties of the CoCrFeMnNi HEA VHCB joints.

Static behavior of stiffened CFST KK joints of offshore wind turbines under antisymmetric loading

This study examines the static behavior of the critical joints of the new kind of offshore jacket foundations under antisymmetric loading by employing a combination of experiments, finite element analysis (FEA), and theoretical derivation. Three tests and 35 FEAs of stiffened concrete-filled steel tubular (CFST) KK joints are described. The introduction of a novel perfobond ring rib (PRB) as a stiffener, along with using a limiting fixture during loading to consider interactions among the four braces, are novelties of this research. Experiments compare the influence of stiffener rib forms (PRB and Perfobond Leister Ribs (PBL)) on the behavior of CFST KK joints, highlighting the superiority of PRB strengthening. However, the influence of the stiffener rib form on the stiffness of the CFST KK joints can be ignored. The properties of PRB-stiffened CFST KK joints are further investigated via validated FEA models, which introduce the modified Mohr-Coulomb (MMC) criterion to realize steel fracture damage. A parametric analysis is then undertaken to explore how variations in the joint's geometrical parameters, chord material strength, and thickness and quantity of the PRBs influence the punching shear capacity of PRB-stiffened CFST KK joints. Furthermore, a formula is presented for punching shear strength in PRB-stiffened CFST KK joints by employing the superposition method. Its predictions align well with both experimental and FEA results.

Characterization of microstructures and mechanical properties of laser welded TWIP steel plate

In the present study, laser welding of medium-thick TWIP steel plates was studied and the microstructures and mechanical properties of the welded joints obtained at varied welding speeds were characterized. It is shown that a full penetration was achieved in the welded joint, which exhibits a keyhole-shaped configuration. The welded joint displays a single austenitic phase and typical solidification structure composed of cellular, columnar and dendrite grains. With increasing the welding speed, the grains in both the central fusion zone and adjacent heat-affected zone were refined. The latter was attributed to inadequate recrystallization because of decreased heating time at elevated welding speed. The mechanical properties of all welded joints were lower than those of base metal, in which the decline of elongation was more serious than that of strength. This is attributed to the formation of thick columnar crystals and the Al2O3 core-shell structured nanoscale precipitates in the grains of the fusion zone. Moreover, there existed a certain degree of non-uniformity in the microstructures and mechanical properties along the thickness direction of welding seam, and the samples in the upper area of welding seam showed better comprehensive properties than the lower ones. When welded at a moderate speed as 1.0 m/min, the welding seams exhibited the best mechanical properties and the least difference across the thickness direction of the welding seam. This is because the moderate welding speed resulted in the most beneficial macro- and micro-structures as well as grain boundary characteristics.

Effect of sintering time on the characteristics of YBCO coated-conductor joints using nano-silver paste

Jointing YBa2Cu3O7-z (YBCO) superconducting coated-conductor (CC) tapes is becoming increasingly significant for magnet applications because of the limited length of single tapes. In this work, YBCO CC tapes stabilized by silver were connected by low-temperature sintering of nano-silver paste. The effect of sintering time and lapped length on the electrical properties of YBCO joints were systematically investigated. And the correlation between microstructure and bonding force of the joints with extending the sintering time was established. It is found that joints sintered within 1∼5 min exhibit relatively lower resistance, while the maximum axial tensile strength at room temperature (RT) was improved with increasing sintering time. Considering the electromechanical properties, ten min is selected as the optimal sintering time for nano-silver paste. The joint by this efficient technology possesses closely connected interface, similar critical current and axial tensile strength (RT) to the single CC tape. The joint resistivity is as low as ∼12.5 nΩ·cm2, which is much less than the traditional soldering joint.

Investigation of interfacial microstructure and connection mechanism of magnetic field-assisted magnesium/aluminum laser welding joint

Variable process experiments to prepare hybrid joints of AZ31 magnesium (Mg) and 6061 aluminum (Al) alloys by magnetic field-assisted laser welding were performed in an overlap Mg-on-Al configuration with the addition of titanium (Ti) foil. Temperature field and flow field of molten pool including chemical potential of each element were also calculated. It is shown that at the optimal welding parameters, the shear force of joint reaches 887.79 N, which is 83.4 % higher than that of no-added joint. In the case of external magnetic field, the improved mechanical properties of joints largely depend on the diffusional barrier effect of Ti foil, which benefits from the enhanced energy absorption and flow of molten pool leading to the enlargement of interface connection area and the formation of Ti-Al compounds such as TiAl3 at Mg/Al interface. Meanwhile, the grains refines due to the magnetic field, which reduces the strain at the joint and enhances the uniformity of the interface microstructure. However, under the condition of excessive magnetic field strength, the enhanced stirring effect of molten pool will cause Ti foil break and the direct interaction between Mg and Al, which deteriorates the joint properties.

On reinforcing the friction stir weld joints of AA5086-H116 using the plasma spray coatings

The fatigue properties of friction stir weld joints of AA5086-H116 alloy, reinforced with Al2O3 particles using the plasma spray coating method, were investigated after single and double weld passes. A relatively uniform distribution of reinforced particles was achieved with superior properties, even higher than that of the parent alloy. The reinforced joints had enhanced hardness as well as joint efficiency, the double pass being superior to the single pass, but at the cost of reduced total elongation. Furthermore, the reinforced double-pass joints exhibited a remarkable ∼ 55%, ∼ 14%, and ∼ 89% increase in fatigue strength compared to the as-weld, the base material, and single-pass joints, respectively. The fractographic examination mainly revealed a defect-free crack initiation mechanism with a few cases of the ones induced by defects. The superior fatigue performance was mainly attributed to the uniform spatial and size distribution of fine Al2O3 particles within the weld nugget zone, thanks to the novel weld reinforcement method used in this study, which provides a promising avenue for improving the fatigue properties of weld joints.

Evolution of microstructure and mechanical properties of GTAW joint for magnesium alloy thin plate by post-weld reinforcement compression treatment

Gas tungsten arc welding (GTAW) joints of magnesium alloy thin plates generally exhibit low welding coefficients. Therefore, post-weld reinforcement compression treatment is utilized to improve mechanical properties of the joints in this experiment. The study shows that the grain shapes and sizes in various zones of the treated welded joints alter significantly, and the presence of twins is also detected especially in the base material (BM) and heat-affected zone (HAZ). The strength of the welded joints progressively rises with the increase in the compression reduction. The welding coefficient of the C3-joint reaches 91.6% when the compression reduction is 1mm. The ultimate tensile strength (UTS), yield strength (YS), and elongation (EL) are 271MPa,173MPa and 7.2% respectively. The post-weld reinforcement compression treatment introduces abundant dislocations in the fusion zone (FZ), contributing significantly to the increase in joint strength. In addition, solid solution strengthening and texture strengthening also exert a role.

Optimization of TLPS Bonding Process and Joint Property using Ni-Sn Paste for High Temperature Power Module Applications

Recently, as interest in eco-friendly vehicles such as electric and hybrid vehicles increases, the demand for power semiconductors, a key component, is also increasing. Power semiconductors convert, distribute, and control power and operate in harsh environments such as high temperature and high pressure. In order to ensure stable reliability in such harsh environments, research on a technology that can stably form joints even at high temperatures is essential. Transitional liquid phase (TLP) bonding was proposed as a high-temperature power semiconductor chip bonding technology, which has the advantage of forming an intermetallic compound (IMC) phase with a high melting point at the joint. However, it takes a long time to convert the joint into full IMC phase. Therefore, in this study, in order to shorten the process time, a paste was manufactured by mixing high-melting point Ni metal powder and low-melting point Sn metal power, and a joint was formed through a TLPS (Transition liquid phase sintering) bonding using the paste. Pastes of different compositions were prepared by adjusting the ratio of Ni and Sn powders. The chip and substrate were bonded through a thermocompression (TC) bonding process, and the highest shear strength was obtained at a bonding temperature of 250 ℃ for 10 min. Heat treatment was performed at 200 ℃ for up to 500 h to evaluate the high temperature long-term reliability of the joints. The Ni-Sn TLPS bonded joints remained reliable joints after a long-term aging test at a high temperature of 200 ℃.

DECISION OF MA 3180/K / PDT/2019 (LEGAL ANALYSIS OF THE SALE AND PURCHASE OF JOINT PROPERTY PRE-DIVISION BY THE TEMPORARY LAND DEED OFFICER)

As stated in Article 36 of Law No. 1 of 1974 respecting joint marriage, any spouse may operate on joint property with a permission. Investigating Supreme Court decision number 3180 K/PDT/2019—which deals with the sale and purchase of undivided joint property in the presence of the temporary land deed officer (PPAT)—and its legal implications is the goal of this research. This study uses conceptual, case, and legislative methods, and it is normative in character. Primary and secondary sources of law are consulted. Legal material analysis is an approach that uses a procedure that is prescriptive. In accordance with the results of the investigation, it is illegal for the PPAT to have issued a deed of sale and purchase and for M.Uzer and Deslina to have sold shares without Herlina's knowledge or approval. Given that the property being sold is still jointly owned, the sale and purchase are declared unlawful according to MA RI No. 701K/PDT/1997. As a consequence, the deed of sale and purchase is legally flawed, and the Certificate of Property Rights in Deslina's name is no longer enforceable.